How long does 7, 11 or 22 kW AC charging take?

Work out the energy you need first, then apply the power your vehicle and installation can actually use. A worked example explains the difference.

Published
INOCHARGE cabled AC charger

Estimate AC charging time by dividing the energy required by the average power available. If you use power measured at the supply, include charging losses in the energy requirement. A wallbox rating alone is not enough. The car, cable, supply and selected settings must all support the proposed session. A 22 kW wallbox therefore does not promise a 22 kW charge for every vehicle.

Begin with the missing energy

Consider a hypothetical car with 60 kWh of usable battery capacity, starting at 20% and aiming for 80%. The change is 60 percentage points, so the approximate battery energy required is 60 × 0.60 = 36 kWh. This example is not a specification for any named car, and the chosen charge window is not a universal battery-care recommendation.

Use usable capacity where available, rather than assuming the advertised gross battery size is available for driving. The car’s displayed state of charge is also an estimate. Your vehicle handbook remains the right place to find the recommended daily charging target.

How do 7/11/22 kW and 10/16/32 A relate?

The INOCHARGE datasheet lists a 400 V line-to-line, three-phase supply and associates 10/16/32 A settings with 7/11/22 kW. For a balanced three-phase load, approximate active power in kW is P = √3 × U × I × power factor / 1000. U is line-to-line voltage and I is line current; the phase currents are not added to create a 30/48/96 A charger setting.

At 400 V with an assumed power factor near 1, the results are about 6.9, 11.1 and 22.2 kW: the product settings use rounded names. These are supply-power estimates, not net battery power or efficiency figures. Schneider Electric’s explanation of three-phase power and current sets out the voltage and power-factor distinction. A separate single-phase example, 230 V × 32 A, gives about 7.4 kW; it does not establish approval to install an INOCHARGE unit on a single-phase supply.

A worked comparison at three power levels

The first calculation below assumes constant power with no losses. The second assumes 90% overall efficiency from the supply to stored battery energy. That efficiency is an illustrative input, not a measured INOCHARGE rating or a promise about a particular car.

Available AC powerIdeal time for 36 kWhWith assumed 90% efficiency
7 kW5 h 9 min5 h 43 min
11 kW3 h 16 min3 h 38 min
22 kW1 h 38 min1 h 49 min

With the efficiency assumption, the supply needs to deliver 36 / 0.90 = 40 kWh. At a constant 11 kW, 40 / 11 is about 3.64 hours, or 3 hours 38 minutes. Rounding to a minute makes the arithmetic readable; it does not make the real-world prediction that precise.

Use the row your car can support

If the hypothetical car accepts a maximum of 11 kW AC, the 22 kW row does not apply even when it is plugged into a 22 kW wallbox. Start with the 11 kW row only if the cable, supply and settings also allow it. A lower installation limit calls for a fresh calculation at that lower power.

Do not substitute a car’s advertised DC rapid-charging figure for its AC limit. AC charging passes through the vehicle’s onboard charger; a DC charging specification describes a different charging path. The car’s documentation should clearly identify which figure you are reading.

Why the session may take longer

An instantaneous power reading is not necessarily the average over the whole session. Battery and ambient temperatures, auxiliary loads, battery condition and the vehicle’s charging strategy can change the result. A scheduled start can also make the total plugged-in period longer than the active charging period.

Manufacturer estimates normally include specific conditions. For an example of how these conditions are presented, see Volvo’s charging-time guidance. Its vehicle-specific figures should not be treated as ratings for other cars, model years or markets.

When comparing your estimate with the car’s display, check the same starting level and target. A prediction to 80% cannot fairly be compared with the time needed to reach 100%. If a session repeatedly differs from expectations, note the settings and displayed power before asking the installer or vehicle support team to investigate.

Cost depends on energy, not just elapsed hours

For a simple energy-cost estimate, multiply supply energy by your applicable unit rate. Using the illustrative 40 kWh total and a hypothetical rate of 5 TRY/kWh gives 200 TRY. This is arithmetic, not a current electricity tariff. Use the relevant rate on your own bill and account for any time bands or additional charges.

Doubling the wallbox’s maximum power does not automatically halve the electricity cost. It can shorten the session when the car and installation permit it. For someone who parks overnight, replacing the energy used each day may be more relevant than the fastest possible full-battery charge.

Turn the estimate into a practical choice

Write down usable battery capacity, starting and target charge levels, the vehicle’s AC limit and the power approved for the installation. Have the supply and proposed setting checked by a qualified professional. Then compare the INOCHARGE cabled and socketed options against the time the car is normally parked. The cable format changes daily handling, while the supported power and energy requirement drive the time estimate.

Before choosing a power value, check how to verify your vehicle’s AC charging capacity and the supply assessment needed for a home installation.

Source links and technical information last checked: 17 November 2026.